• Skip to main content
  • Skip to header right navigation
  • Skip to site footer

1-800-685-2088 | support@mat-cs.com

  • LinkedIn
MAT-CS - Materials Characterization Services

Materials Characterization Services

  • Home
  • About
    • Meet the Team
    • Consulting
  • Analytical Techniques
    • Bulk Analysis
    • Microscopy and Microanalytical
    • Surface and Thin Film
    • Polymer Characterization
    • Optical Measurements
    • Liquids and Gases
    • Electrical / Electronics
    • Reliability Testing
    • Miscellaneous
  • Test Methods
    • ASTM Methods List
    • ISO Methods List
    • AATCC
    • AOAC
    • AOCS
    • EPA, SM
    • FDA BAM
    • IP
    • JEDEC
    • MIL-STD
    • OCSPP
    • OPPTS
    • REACH
    • RoHS
    • SEMI
    • TAPPI
    • USP/EP/JP
  • Resources
    • Experiment Design
    • Consulting
    • The Laboratory Landscape
    • Quality Programs
    • Regulatory-Based Analyses
  • Contact
  • Get a Quote!
MAT-CS Home Cover

ASTM C465

ASTM C465 – Standard Specification for Processing Additions for Use in the Manufacture of Hydraulic Cements

Description:

Abstract

This specification covers the criteria and tests to be used for determining whether a processing addition meets the requirement. When proposed addition is accepted for general use in Portland cement, tests shall be made on cements prepared from at least five different clinkers. These clinkers shall represent two Type I cements, one Type II cement, and two Type III cements. Processing additions shall be evaluated by comparing cements containing the addition to otherwise identical cements from the same source without the addition, or containing a processing addition. The compressive strength and flexural strength of the concrete made with cement containing the addition shall be compared with strengths obtained with the control cement at similar ages. The properties of the materials shall be determined through the following tests in accordance with the following standard: chemical analysis of the cement, compound composition, fineness of cement, normal consistency, time of setting, autoclave expansion, air content of mortar, compressive strength of mortar, and drying shrinkage of mortar.

Scope

1.1 This specification pertains to the criteria and tests to be used for determining whether a(n) organic or inorganic processing addition, when used in the recommended amount at the option of the cement producer in the manufacture of hydraulic cements, meets the requirements as prescribed by definition in Specifications C150/C150M, C1157/C1157M, C845/C845M, and C595/C595M. The materials listed in the following former ASTM Specifications shall be considered as meeting the organic processing additions requirements of this specification:

 C150/C150M – 62, for Portland Cement 
 C205 – 58 T, for Portland Blast-Furnace Slag Cement 
 C340 – 58 T, for Portland Pozzolan Cement 
 C358 – 58, for Slag Cement 
 

1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

Related Test Methods

ASTM D483

ASTM D4829

ASTM D4828

ASTM D4824

ASTM D482

ASTM D4815

ASTM D4814

ASTM D4812

ASTM D4811

ASTM D4810

ASTM D4809

ASTM D4808

Previous Post:MAT-CS Home CoverASTM C457
Next Post:ASTM C469MAT-CS Home Cover

Ready to start your analysis?

Get a Quote!
MAT-CS

Your One Source for Materials Analysis

1-800-685-2088

support@mat-cs.com

  • Home
  • Analytical Techniques
  • Test Methods
  • Resources
  • Contact Us
  • Get a Quote!
  • Special Analysis Request

  • LinkedIn

Copyright © 2025 by Materials Characterization Services · All Rights Reserved
Website Built, Hosted, and Managed by Digital Donkey Marketing