Materials Characterization Services
Search for Analytical Techniques and Test Methods
We are currently working on updating our list of supported methods. If you don’t see the test method you need below, please submit a special request with details about the method you need and we will check to see if we can provide it.
ASTM D2180 – Standard Test Method for Active Oxygen in Bleaching Compounds Description: Abstract This test method covers the determination of inorganic active oxygen in bleaching compounds such as perborates, percarbonates, and peroxides by titration of an acidified aqueous solution with a standard solution of potassium permanganate. Tests shall use reagent grade chemicals, reagent water, …
ASTM D2178 – Standard Specification for Asphalt Glass Felt Used in Roofing and Waterproofing Description: Scope 1.1 This specification covers glass felts impregnated to varying degrees with asphalt intended to be used with asphalts conforming to the requirements of Specification D312/D312M or D7654/D7654M in the construction of built-up roofs, and with asphalts conforming to the requirements of Specification D449/D449M in the construction …
ASTM D2172 – Standard Test Methods for Quantitative Extraction of Asphalt Binder from Asphalt Mixtures Description: Significance and Use 4.1 All of these test methods can be used for quantitative determinations of asphalt binder in asphalt mixtures and pavement samples for specification acceptance, service evaluation, control, and research. Each method prescribes the solvent or solvents and …
ASTM D2171 – Standard Test Method for Viscosity of Asphalts by Vacuum Capillary Viscometer Description: Significance and Use 5.1 The viscosity at 60 °C [140 °F] characterizes flow behavior and may be used for specification requirements for cutback asphalt and asphalt binders. NOTE 3: The quality of the results produced by this standard are dependent on the competence of …
ASTM D2170 – Standard Test Method for Kinematic Viscosity of Asphalts Description: Significance and Use 5.1 The kinematic viscosity characterizes flow behavior. The method is used to determine the consistency of liquid asphalt as one element in establishing the uniformity of shipments or sources of supply. The specifications are usually at temperatures of 60 and 135 °C. …
ASTM D217 – Standard Test Methods for Cone Penetration of Lubricating Grease Description: Significance and Use 5.1 These cone penetration tests not only evaluate the consistency of lubricating greases over the full range of NLGI numbers from 000 to 6, but also evaluate the consistency of stiff greases having penetration numbers less than 85. In contrast, …
ASTM D2166 – Standard Test Method for Unconfined Compressive Strength of Cohesive Soil Description: Significance and Use 5.1 The primary purpose of the unconfined compression test is to quickly measure the compressive strength for those soils that possess sufficient cohesion to permit testing in the unconfined state. The test is performed on non-free draining soils at …
ASTM D2164 – Standard Methods of Testing Structural Insulating Roof Deck (Withdrawn 2005) Description: Scope 1.1 These methods cover determination of the following properties of structural insulating roof deck. In all structural tests the specimens are loaded as beams with the finished (ceiling) face in tension. Sections Equivalent Uniform Load 8-12 Concentrated Load 13-16 Sustained …
ASTM D2163 – Standard Test Method for Determination of Hydrocarbons in Liquefied Petroleum (LP) Gases and Propane/Propene Mixtures by Gas Chromatography Description: Significance and Use 5.1 The hydrocarbon component distribution of liquefied petroleum gases and propene mixtures is often required for end-use sale of this material. Applications such as chemical feed stocks or fuel require precise …
ASTM D2161 – Standard Practice for Conversion of Kinematic Viscosity to Saybolt Universal Viscosity or to Saybolt Furol Viscosity Description: Significance and Use 4.1 At one time the petroleum industry relied on measuring kinematic viscosity by means of the Saybolt viscometer, and expressing kinematic viscosity in units of Saybolt Universal Seconds (SUS) and Saybolt Furol Seconds …
